Bambu Lab SuperTack Pro Plate H2S & H2D

The Bambu Cool Plate SuperTack Pro is a flexible spring-steel build plate developed for reliable PLA and PETG printing without regularly applying glue or other adhesives.

Its SuperTack Pro coating securely holds the first layer during printing, helping prevent lifted corners, detached supports, and failed prints. This improved adhesion is particularly useful for large objects, tall models, narrow contact areas, and parts that are prone to warping.

Compared with the original SuperTack plate, the Pro version is designed to operate at lower heatbed temperatures. Bambu Lab recommends approximately 40°C for PLA and 60°C for PETG, compared with 45°C and 70°C respectively for the original SuperTack plate.

Strong First-Layer Adhesion

The SuperTack Pro coating provides excellent contact between the print and build surface, helping eliminate common adhesion problems.

It can help reduce:

• Lifted corners
• Warping on large models
• Detached supports
• Failed first layers
• Movement during tall prints
• Adhesion problems caused by small contact areas

The plate is designed specifically for dependable PLA and PETG printing.

Lower-Temperature, Energy-Efficient Printing

Because the coating maintains strong adhesion at lower temperatures, the printer does not need to keep the heatbed as hot as it would with many conventional build surfaces.

Smooth Matte Surface Finish

The SuperTack Pro coating leaves a smooth, natural-looking matte texture on the bottom of the printed model.

This can help the build-plate side blend more naturally with the remaining printed surfaces, making it suitable for:

• Decorative models
• Functional parts
• Display pieces
• Multi-part assemblies
• Products where the bottom surface remains visible

Reduces Warping on Large Prints

Large objects can generate significant internal stress as the material cools. The strong adhesion of the SuperTack Pro surface helps hold the model securely and reduce lifted corners during printing.

This makes the plate particularly useful for:

• Large storage organizers
• Wide enclosures
• Long functional components
• Models with sharp corners
• Parts with a large first-layer footprint

Durable, Long-Lasting Coating

The specially designed surface maintains consistent adhesion through repeated printing. Bambu Lab reports less than a 15% reduction in adhesion after 300 prints under its test conditions.

As with all coated build plates, lifespan depends on cleaning methods, print settings, material selection, scraper use, and general handling.

Easy Model Removal

Allow the plate and printed model to cool before removal. The coating is designed to reduce adhesion after cooling, making parts easier to release.

Use the scraper supplied with the printer to gently lift an edge, then carefully remove the model. When a print remains firmly attached, Bambu Lab recommends heating the plate to approximately 50°C to assist with removal. The coating is relatively soft, so avoid digging the scraper into the surface.

Cleaning and Maintenance

The SuperTack Pro normally provides strong adhesion without applying adhesive or cleaning the surface before every print.

When the plate becomes dirty:

• Wash it with water and ordinary dish soap.
• Rinse away all soap residue.
• Allow the plate to dry completely.
• Avoid touching the printing area with bare fingers.
• Do not clean it with acetone or other organic solvents.

Organic solvents can permanently damage the SuperTack Pro coating.

Key Features

• Strong adhesion for PLA and PETG
• Lower heatbed temperatures
• Reduced energy consumption
• Helps prevent first-layer failures
• Reduces warping on large objects
• Smooth matte bottom-surface finish
• Adhesive-free printing for supported materials
• Flexible spring-steel construction
• Magnetic installation
• Fine-tuned release after cooling
• Durable coating for repeated use
• Multiple sizes for compatible Bambu Lab printers

Important Notes

• Confirm that you have selected the correct plate version for your printer.
• The coating can be damaged by aggressive scraping.
• Do not use acetone or other organic solvents.
• Remove models carefully rather than sharply pulling them from the surface.
• Allow the plate to cool unless the model is adhering too strongly.
• For very firmly attached parts, heat the plate to approximately 50°C before removal.
• Filament formulations vary, so confirm compatibility before printing third-party specialty materials.

Bambu PLA Silk+ is supported, but Bambu Lab warns that some other PLA Silk materials may adhere excessively. For third-party PLA Silk, use the appropriate Bambu Studio preset and evaluate compatibility carefully.

In the Box:

• 1 x Bambu Lab SuperTack Plate for the H2S and similar size printers

Compatibility

• Bambu Lab H2S
• Bambu Lab H2D
• Bambu Lab H2D Pro