Micro Swiss

Micro Swiss MK10 All Metal Hotend Kit with Slotted Cooling Block

(6 reviews) Write a Review
SKU:
MS-FULL-MK10040
  • Micro Swiss MK10 All Metal Hotend Kit with slotted cooling block
  • Micro Swiss MK10 All Metal Hotend Kit with slotted cooling block
  • Micro Swiss MK10 All Metal Hotend Kit with slotted cooling block
$65.00

Description

Free shipping in Canada for orders over $140 before tax. (via Canada Post)

This is Micro Swiss All Metal Hotend kit with redesigned cooling block for Wanhao i3 with the following improvements:

  • Slotted Clamping system
  • No set screw to ding and damage thermal tube
  • Significantly better heat transfer (this is a big one!!!)
  • Easier disassemble and adjustments
  • Precise control on bore diameter

Micro Swiss All Metal Hotend Kit Features:

All metal hotend upgrade for MK10 style extruders. This upgrade includes a modified thermal barrier tube and modified nozzle with modified cooling block. Thermal barrier tube is made from 2 different materials. The lower thermal break is made from stainless steel, and the colder upper part is made from aluminum. Stainless steel was used for thermal break because it offers low thermal conductivity, and aluminum was used for the upper portion because it has a lot better thermal conductivity, to carry away any heat from the filament. All metal hotend will let you print at much higher temperature then possible with original PTFE lined one. Another benefit of an all metal hotend design is more consistent melt chamber control. During slow extrusion rate, in PTFE lined hotend, transition zone from solid to molten plastic tends to creep upward creating more stringy prints. With all metal design a transition zone is always constant, being located right at the heat break. With fast extrusion rate, PTFE tube doesn't have enough thermal conductivity to properly melt all the plastic coming out. On MK10 extruders that limitation happens around 60 mm/s, depending on nozzle size. All metal hotend solves this problem, plastic is surrounded by thermally conductive nozzle throughout its length.

CNC Machined and Assembled in USA

Installation Instructions

Kit will fit:

  • Wanhao i3
  • Wanhao i3 Plus
  • Monoprice Maker Select 3D Printer v2
  • Monoprice Maker Select Plus
  • Cocoon Create 3D Printer

Kit includes

  • 1 Plated brass Wear Resistant Nozzle (0.4mm)
  • 1 Thermal tube
  • 1 Slotted Cooling block

Buy a Micro Swiss all metal hotend for the Wanhao Duplicator i3 in Canada without the surprise cost of the exchange rate!

View AllClose

Videos

View AllClose

6 Reviews

  • 5

    Great extruder!

    Posted by Pierre-Luc Gagnon on July 27, 2018

    I have nothing bad to say about the Micro-Swiss Mk10 extruder kit. It's great and it's super easy to install. One thing I didn't know is that the Wanhao Duplicator i3 Mk2 does have an all-metal extruder already. This is for non-mk2 printers. Oh well, I now have a Genuine Micro-Swiss installed on my i3+Mk2 and if something ever happens I still have the stock one packed away. Get one but don't get one if you have a Duplicator i3 Plus Mk2.

  • 5

    micro swiss hot end

    Posted by Garvin Griswold on May 15, 2018

    The micro Swiss hot end made my Monoprice. Select V2 into a real printer. Prints flawlessly never runs out of filament. Couldn’t be happier.

  • 5

    Should have done this long ago ;-)

    Posted by Rob Stevens on October 30, 2017

    I have been happy with my Wanhao i3 but found the nozzle clogs more often than my other printers. I put in the Micro Swiss all metal hot end and found the print quality improved. Time will tell if the clogging reduces.

  • 5

    Easy install and instant results.

    Posted by AdamantiumInc on June 27, 2017

    I've installed these on both my Monoprice Maker Select V2 I think from start to finish it takes about 10-15 minutes to install. No more worrying about PTFE tubes clogging. No lag on a brim or skirt layer from when it starts printing and I'm able to get beautiful prints at 100mm/s.

  • 5

    Works Perfectly - Fits Hictop I3 with minimal mods

    Posted by Billy on April 11, 2017

    It sure is a good upgrade to any printer. It does improve the quality of my print. I tried it with Colorfabb XT carbon and FormFutura metalFill Bronze and its a charm to work with.

  • 5

    Great upgrade

    Posted by Ron O on March 13, 2017

    I used the stock nozzle for 3 months, the internal plastic tube began to deform and my filament would often jam between prints. The new nozzle can't deform and has less friction when I insert or retract the filament when unloading and loading filament. I increased the head temperature 5 degrees as recommended by MicroSwiss and it has been working perfectly. Also noticed that filament does not stick as easily to the head so I have less issues with the head becoming messy.

View AllClose

Related Products

Related Products

Out of stock
Micro Swiss MK10 All Metal Hotend Kit - 3D Printer Spare Parts

Micro Swiss MK10 All Metal Hotend Kit

Micro Swiss

$49.00
Free shipping in Canada for orders over $140 before tax. (via Canada Post) This is an all metal hotend upgrade kit for MK10 style extruders. The thermal barrier tube is made from 2 different...
Out of stock
Micro Swiss MK10 with slotted cooling block 3D printing Canada

Micro Swiss MK10 Slotted Cooling Block

Micro Swiss

$29.00
Free shipping in Canada for orders over $140 before tax. (via Canada Post)   This is redesigned cooling block for Wanhao i3 with the following improvements: Slotted Clamping system No set...