*E3D V6 Gold Hotend Full Kit - 1.75mm

$139.00 - $159.00

Create Wishlist

Voltage *
Assembly *

Free shipping in Canada for orders over $140 before tax. (via Canada Post)

 Original Prusa printers require the Prusa heatbreak if you use the MMU system - https://spool3d.ca/prusa-e3d-v6-heat-break/ 

To celebrate the E3D V6’s third birthday we wanted to do something special to show off the HotEnd that spawned a whole ecosystem. More than just bling, the Gold edition V6 has been upgraded with some of the very best components available from E3D, at a lower price point than purchasing components individually. We upgraded the following stock components for the best we sell in order to create the bacon of HotEnds:

01. Golden Heat Sink

We’ve blinged up the heat sink with gold anodising, so that everyone can see from 10 yards away that you are a fancy individual who will only accept the best of the best in HotEnd technology..

02. Heater Block

We’ve switched the aluminium heater block for a plated copper-alloy block, again increasing heat transfer to the filament and reducing the chance of filament goo sticking to it. This reduces the need for a sock, so that you can show off the shiny engraving.

03. Nozzle

The standard brass nozzle has been swapped in favour of hardened steel. Whereas brass nozzles can be worn down and even ruined by abrasive materials, hardened steel will last a lifetime. If you print with carbon fibre, filled filaments, or even glow in the dark filament then these nozzles are a must.

04. Heater Cartridge

We’ve swapped standard heaters for our upcoming high precision, quick release heater cartridges. Spot-on physical dimensions and electrical specifications guarantee perfect performance. Quick release also makes tinkering with your HotEnd a doddle.

05. Fan Duct

A clear, moulded plastic fan duct shows off the beautiful golden heatsink to its very best.

06. PTFE Guide

We’ve upgraded the standard PTFE guide to High Tolerance Capricorn PTFE Tubing. This new bowden tubing has a tight diameter and much-reduced friction, giving smoother, more accurate extrusion.


What's included:

Metal Parts

  • 1 x Special Edition Gold Anodised Heatsink
  • 1 x 1.75mm Stainless Steel Heat Break
  • 1 x 1.75mm x 0.4mm Hardened Steel V6 Nozzle
  • 1 x Plated copper Heater Block
  • 1 x Thermistor Cartridge
  • 1 x 30x30x10mm fan (12V or 24V)
  • 2 x Connector Cable
  • 1 x 30W High Precision Heater Cartridge (12V or 24V)
  • 1 x Fibreglass Insulated Heater Connector Cable
  • 1 x Fan Duct
  • 1 x Silicone Sock
  • 1 x Thermal Compound Sachet
  • 1 x Fixings Kit
  • 800mm x High Tolerance PTFE
  • Collet Clip
Buy a genuine E3D V6 hotend assembly from #Spool3D for your 3D printer in Canada without the surprise cost of the exchange rate!
SKU: V6-175-GOLD


4 out of 5 (based on 3 ratings)
leave a review

Replacement kit for my MK3S

Perfect fit. Bought the 40w cartridge heater as well to use instead of the 30W included in kit. Lots of instructions and videos online with step-by-step procedures. First time doing this myself and it was straight forward.
Posted by Ryan M, June 28, 2020

MK3S incompatibility

If you use this kit with a MK3S you'll need to slow it down, the heater cartridge runs 10W less than the factory one and it will cause all sorts of problems with the default settings in Prusa slicer.
Posted by David, October 12, 2019

A pleasure to use.

This is my first hotend that I have ever used personally and I bought it with the intent of using nylons and abrasive plastics. The thermistor is now being used in my heatbed as I upgraded to a PT100 on this hotend. I also upgraded to a Titanium heat break and these upgrades have made this hotend an absolute pleasure to use. I was using PLA printed components on the printer to start with and the groove mount didn't even get warm wile printing at 230C. The capricorn tubing is working beautifully with the Titan extruder I also bought. Also GOLD.
Posted by Devon Pearce, November 12, 2018