E3D Online

E3D Thermistor Cartridge

(16 reviews) Write a Review
SKU:
E-SEMITEC-50-MOLEX-INC-CABLE
  • E3D Thermistor Cartridge - 3D Printer Spare Parts
  • E3D Thermistor Cartridge - 3D Printer Spare Parts
$9.00

Description

Free shipping in Canada for orders over $140 before tax. (via Canada Post)

A replacement E3D cartridge type Semitec 104Gt thermistor suitable for all E3D HotEnds using a cartridge type Heater block.

Thermistor cartridge 

Cartridge type thermistors use a Semitec 104NT thermistor, potted in a cylindrical stainless steel cartridge with a high conductivity ceramic based adhesive.

The legs are insulated with fibreglass sleeving and terminated with a Molex Microfit 3.0 connector.

This makes it easy to disconnect your entire HotEnd without the need for rewiring, especially when paired with our high precision heater cartridges.

Key features: 

  • Max temperature rating: 285°C
  • Cartridge diameter: 3mm 
  • Cartridge length: 15mm 
  • Cable Length: 50mm
  • Cable Colour: Blue
  • Connector type: Molex Microfit 3.0

Kit includes: 

  • 1 x Thermistor cartridge 
  • 1 x Thermistor extension cable 

Documentation

  • Type 5 thermistor in Marlin Firmware

Buy an E3D thermistor cartridge from Spool3D for your 3D printer in Canada without the surprise cost of the exchange rate!

View AllClose

16 Reviews

  • 4

    Good quality thermistor but wires should be longer.

    Posted by Stefan on July 03, 2018

    I have Installed this thermistor with a new block and heating element on my Prusa i3 MK2 and I find the wires slightly to short to clear properly the metal frame when it goes home on X axis. Is difficult to keep the plastic connector away from the metal frame as have to be kept under the other wires. If the wires would be 12-15 mm longer would be perfect.

  • 5

    Replacement

    Posted by Daniel Tousignant-Brodeur on February 26, 2018

    Its replacement for the original part and behaves as such. Just swap it in and its done.

  • 4

    Good Product, Quick Shipping

    Posted by Unknown on January 11, 2018

    This replaced my first/identical thermistor; the ends of which wore and broke off, but lasted a heavy amount of printing. Worth ordering an extra to have on hand.

  • 4

    Great thermistor for Prusa i3 MK2S

    Posted by Jeff on August 24, 2017

    Great thermistor for my Prusa i3 MK2S and fast delivery. The only downside was the connector between the wire of thermistor and the other extension set of wire. This create an interference when the X axis go and snap the limit switch. To solve this issue, I had to remove the 2 blue thermistor's tiny cable from the connector and use my broken thermistor wire to attach them to my older i3 MK2S thermistor cable that is connected to the board. A suggested improvement would be to provide longer blue cable from thermistor so the connector can be attach to the harness without interferring with the i3 MK2S frame. Not a big issue and I recommend it to any i3 MK2S user that need to fix a broken wire/thermistor.

  • 5

    works great with prusa i3 mk2s

    Posted by devinradcliffe@gmail.com on June 15, 2017

    I installed this after my old style e3dv6 thermistor was severed by a blob of PLA. Slid right into the hot end and interfaced perfectly with the RAMBO board.

  • 4

    Really good quality but

    Posted by Unknown on March 14, 2017

    This thermistor is really good quality but when placed into the newer e3d hot end with the thumb screw I screwed it only until I felt a bit of give (so as to keep the sensor in there). Apparently, even that was a bit much as the thermistor started to short out and give me a negative reading. I will probably buy this one again but be even more careful with it this time as it is a very sensitive piece of metal.

View AllClose