E3D

*E3D V6 Direct Hotend Full Kit - 1.75mm Universal

$79.00
Voltage *

Free shipping in Canada for orders over $140 before tax. (via Canada Post)

 

E3D-v6: Smaller - Easier - Higher Performance.

Hotends have the new heater block and thermistor cartridge introduced in June 2016.

Assembly guidelines for the v6 can be found here.


Print the Widest Range of Materials Possible.

 

 

Building on E3D's signature high temperature performance that allows you to print high temperature materials E3D has now focussed on adding increased functionality with soft and flexible filaments. By providing a PTFE liner tube through the hotend that you can extend into your extruder this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments like NinjaFlex, FlexPLA and FlexPolyester. This opens up a huge range of new opportunities for your printer.

(PTFE Liner only present in 1.75mm version - 3mm Bowden has partial lining - 3mm Direct has no lining)

v6-175.jpgv6-300-d2.jpgv6-300-b.jpg

This above cutaways show the internals of all three HotEnds. Left to Right: 1.75mm Universal, 3mm Direct, 3mm Bowden.

 


High Temperature Peformance.

 

 

With no PEEK or PTFE in hot regions of the E3D V6 HotEnd you can reach 300C with the supplied thermistor. By swapping a thermistor for a thermocouple (may require additional electronics) you can reach over 400C. 

This not only allows you to print extremely high temperature materials like Polycarbonate and Nylons but also eliminates HotEnd meltdown failures associated with PEEK/PTFE designs. Although E3D's latest v6 hotend has a PTFE liner inside the hotend this liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating.

The new HeaterBlock gives the fastest heat up times and the most responsive temperature control by clamping around the cartridge for maximum thermal contact. The new thermistor placement means you get the most accurate temperature readings with the fastest response. What this means for you the user, is that you can go from 20C to 200C in just 65 seconds, temperature control is responsive enough that you can keep the hotend within 0.5C of your set temperature or less with ease.

 

Package Contents:

  • Genuine unassembled E3D V6 Full direct Kit - 1.75mm filament; 12V or 24V heater cartridge; 0.4mm brass nozzle, V6 silicone sock, 30mm fan
  • 0.15m PTFE tubing

Buy a genuine E3D V6 hotend assembly from #Spool3D for your 3D printer in Canada without the surprise cost of the exchange rate!

SKU: E3DV6-175##DIR

Reviews

4 out of 5 (based on 6 ratings)
leave a review

Best upgrade so far

5/5
Plenty of instructions online. The print quality is way better than my old Ceramic Ubi hotend, it doesn't even compare.
Posted by Pete, March 30, 2018

great quality prints

5/5
Purchased this to finish Christmas presents. Print quality is great compare to stock hex end. Had some issues with assembly but more my fault then anything. Would of been nice if instructions were provided but nothing YouTube couldn’t solve.
Posted by Luke, December 26, 2017

Clone works better

2/5
I have more failed prints with this Genuine E3D V6. Will keep on trying but so far not impressed.
Posted by undefined, September 23, 2017

Works Great

5/5
Installed on Prusa i3 MK2 - everything is working fine.
Posted by undefined, August 11, 2017

great hot end

5/5
Installed on my rigidbot big. Works great! Fast shipping.
Posted by undefined, January 25, 2017

awesome hotend super reliable

4/5
It was easy to assemble and setup. Prints come out great and I've yet to have it clog up.
Posted by undefined, October 27, 2016