E3D Online

E3D Revo CR Hotend

$119.00 - $189.00

Create Wishlist

Close
Kit Type *
Voltage *

Free shipping in Canada for orders over $140 before tax. (via Canada Post)

Upgrade your Creality 3D printer to Revo so you can change nozzles cold without special tools and hot tightening hassles.

No extra mounts or adapters needed: Pre-drilled M3 clearance holes match Creality’s X carriage mounting pattern for easy installation.

No firmware tweaks: This kit includes a special Revo HeaterCore with a 100K NTC thermistor, which has the same response as the stock Creality thermistor.

Includes solderless, crimp-less, butt splice connectors for easy connection. Wire the HeaterCore into your Creality 3D printer without undoing your entire cable bundle

Detailed upgrade guides created by E3D help you get 3D printing quickly

Creality mounting holes. Convenient M3 clearance holes correspond to Creality’s X carriage mounting pattern, so you can get up and running quickly without extra mounts or adaptors. Just reuse the existing M3 bolts!

Easy nozzle swaps. A variety of Revo Nozzles enhance the capabilities of your 3D printer without a difficult nozzle changing processes. Every Revo Nozzle can be changed by hand. No tools, no hot tightening.

Simple, hassle-free connection. We’ve included some solderless, crimpless, butt splice connectors for easy connection to help you get up and running quickly without having to undo your entire wiring bundle.

Better reliability. Revo Nozzles are factory sealed, so there’s much less chance of nozzle leaks, and no hot tightening needed.

Better efficiency. The included Revo HeaterCore makes your 3D printer heat up faster and more efficiently than the stock HotEnd. Start 3D printing right away without annoying firmware adjustments: we’ve integrated a 100K NTC thermistor into this special HeaterCore. This thermistor has the same response as the stock HotEnd, so no firmware tweaks are needed. Better safety. Thanks to built-in PTC behaviour of the heaterCore, Revo CR will add an extra failsafe against thermal runaways to your Creality 3D printer – providing an extra layer of protection if thermal runaway protection is disabled in firmware.

Is Revo CR compatible with my Creality printer?

Please see the E3D compatibility guide for the most up-to-date information.

Please note:

  • Revo CR can be used with other Creality printers using the NTC thermistor. However, you may need to modify the mount and or Z sensor.
  • You may need to adjust the Z height when changing nozzles.
  • Please check whether your specific printer runs 12V or 24V before purchasing and assembling.

Key features:

  • Max temp: 300°C
  • Nozzle: RapidChange Revo
  • Solder and Crimping free wiring
  • Temperature sensor: Creality specific
  • Mounting type: Creality M3

Kit includes:

  • 1 x Revo CR heatsink
  • 1 x Collet
  • 1 x Collet clip
  • 1 x Revo HeaterCore 12V or 24V
  • 1 x Revo HeaterCore spring
  • 1 x Extension cable kit
  • 4 x butt splice connector

Single nozzle kit:

  • 1 x 0.40mm brass Revo Nozzle

Fully loaded nozzle kit:

  • 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles

Buy an E3D Revo CR hotend kit from Spool3D for your 3D printer in Canada without the surprise cost of the exchange rate!

SKU: REVO-CREALITY

Reviews

5 out of 5 (based on 1 rating)
leave a review

My favourite hot end

5/5
The system they designed for this hot end means almost zero downtime for my machines. It also heats very fast and uniformly. This is what I will be changing all my machines to since it is almost impossible to clog the nozzles anyways. And no tools required!
Posted by William Robinson, April 27, 2023